Net framework pentru xlovecam flux manager!
buna ziua, seara la toata lumea am si eu o problema si ma gadeam ca poate am noroc sa o rezolv. :roll: este in legatura cu xlovecam am cont la ei de ceva timp, 2 anisori ,zic eu sii acum au bagat Flux Manager ....acum ceva timp...l-am tras dupa site dar imi cere NET FRAMEWORK 2050727 (lucrul acesta ) :oops: l-am cautat sa-l trag dupa net nu l-am gasit decat cu banutii . va rog frumos daca ma puteti ajuta :roll: am o camera video aparent buna si ma gadeam ca ar fii si mai bine cu SUPER flux-ul managerul .
- SAD^^EYES
- Administrator
- Mesaje: 2704
- Membru din: 02 Mai 2004, 18:48
- Localitate: Romania
- Has thanked: 129 times
- Been thanked: 78 times
- Contact:
http://www.microsoft.com/downloads/deta ... laylang=en
mai jos in pagina aia gasesti si update-uri ... baga si versiunea 3.0 sa fie acolo
mai poti lua net framework prin windows update (optionale)
Bafta acolo
mai jos in pagina aia gasesti si update-uri ... baga si versiunea 3.0 sa fie acolo
mai poti lua net framework prin windows update (optionale)
Bafta acolo
- XtremeStudio
- User Junior+
- Mesaje: 191
- Membru din: 15 Aug 2008, 20:20
- Localitate: Iasi, Pascani
- Has thanked: 0
- Been thanked: 0
- Contact:
Cause: This error occurs because the rollback feature of the Microsoft Windows Installer is disabled. The .NET Framework Setup program requires commit custom actions for proper installation. Rollback and commit custom actions do not run when rollback is disabled.
Rollback is disabled in the DisableRollback policy in the registry. The DisableRollback policy value may have been set by an administrator. Microsoft recommends that administrators do not disable rollback unless this is necessary.
Rezolution : Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems might occur if you modify the registry incorrectly. Therefore, make sure that you follow these steps carefully. For added protection, back up the registry before you modify it. Then, you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following article number to view the article in the Microsoft Knowledge Base:
322756 (http://support.microsoft.com/kb/322756/ ) How to back up and restore the registry in Windows
There are two places in the registry where the DisableRollback policy value can be set. To resolve this problem, you must find out where the DisableRollback policy was set and remove or disable the setting.
To find out whether this property exists in your registry, run C:\Regedit.exe and check the following locations:
HKEY_LOCAL_MACHINE\Software\Policies\Microsoft\Windows\Installer\DisableRollback
HKEY_CURRENT_USER\Software\Policies\Microsoft\Windows\Installer\DisableRollback
If the DisableRollback key exists and has a value of "1", delete the key or set the value of the key to "0". (You can also set DisableRollback through command-line instructions.) Microsoft recommends that administrators and developers not set this property if they use command line instructions to run Setup, or Setup will not work.
Sper sa te descurci daca nu am sa repostez in lb. Romana
Rollback is disabled in the DisableRollback policy in the registry. The DisableRollback policy value may have been set by an administrator. Microsoft recommends that administrators do not disable rollback unless this is necessary.
Rezolution : Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems might occur if you modify the registry incorrectly. Therefore, make sure that you follow these steps carefully. For added protection, back up the registry before you modify it. Then, you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following article number to view the article in the Microsoft Knowledge Base:
322756 (http://support.microsoft.com/kb/322756/ ) How to back up and restore the registry in Windows
There are two places in the registry where the DisableRollback policy value can be set. To resolve this problem, you must find out where the DisableRollback policy was set and remove or disable the setting.
To find out whether this property exists in your registry, run C:\Regedit.exe and check the following locations:
HKEY_LOCAL_MACHINE\Software\Policies\Microsoft\Windows\Installer\DisableRollback
HKEY_CURRENT_USER\Software\Policies\Microsoft\Windows\Installer\DisableRollback
If the DisableRollback key exists and has a value of "1", delete the key or set the value of the key to "0". (You can also set DisableRollback through command-line instructions.) Microsoft recommends that administrators and developers not set this property if they use command line instructions to run Setup, or Setup will not work.
Sper sa te descurci daca nu am sa repostez in lb. Romana
bun pana acum toate bune dar....am ajuns pana la partea cu installer si aici am 2 variante default si enable-adminTSR eu ca sa fiu sigura ca-mi termin calculatorul am bagat 0 peste tot
:roll: daca se mai poate sa ma scoata cineva din ceata asta groasa va rog frumos. multumesc :roll:
:roll: daca se mai poate sa ma scoata cineva din ceata asta groasa va rog frumos. multumesc :roll: